Demand Branch Properties

See also: Analysis View, Demand Analysis, Final Energy Demand Analysis, Useful Energy Demand Analysis, Activity Analysis, Stock Analysis, Transport Analysis

Use this screen to edit the properties (name, type, etc.) of a demand branch.  Note that some of the options shown here (e.g. Energy Demand, Fuel) will only appear when relevant.  The options displayed depend on the type and properties of the branch.

Demand branches can be the following types:

Category branches are used mainly for organizing the other branches into hierarchical data structures. These branches only contain data for Activity Levels, Costs and any User Variables.

Category With Energy Intensity branches are used to indicate a category branch at which energy intensities are specified at one level up from the actual energy-using technologies.  These types of branches are used in three cases:

a) where you have energy intensity data for an end-use and have fuel share data (not intensity data) for the fuels and devices below the end-use,

b) where you have devices that use more than one fuel, or

c) where you wish to conduct a Useful Energy Demand Analysis.

In this latter case you need to check the additional Useful energy analysis check box on the branch properties screen. When conducting a useful energy analysis, you can choose to enter current accounts data for the end-use in two different ways. Check the Final Energy Intensities in Current Accounts check box to specify final energy intensities (i.e. the amount of fuel used) or leave the box unchecked to specify useful requirements (i.e. the service demand) in Current Accounts. In either case you will always enter the useful demand for other scenarios. .

Technology with Energy Intensity branches are used to specify final energy consuming technologies, and hence when choosing this type of branch you will also need to select the fuel consumed.  Use this type of technology branch when you want to project energy consumption as the product of an activity level and an energy intensity.

When conducting a useful energy demand analysis, you can optionally specify a co-product that is produced when the technology operates. For example, a demand for heat in buildings could be met using a combined heat and power (CHP) unit that consumes natural gas but also produces electricity as a coproduct.  Note that only technologies created below a green category branch () can have co-products in which a useful energy analysis has been enabled can have a co-product.  If you specify a co-product, an additional variable (tab) will appear in the main data entry screen in which you can specify the co-product efficiency. Note that the sum of the efficiency and co-product efficiency must be less than or equal to 100%.

Technology with Total Energy branches are used to specify final energy consuming technologies, and hence when choosing this type of branch you will also need to select the fuel consumed.  Use this type of technology branch when you want to project energy consumption directly by entering data on the total energy consumed.  In other words, this type of branch ignores any data entered in the Activity level variable.

Stock Analysis branches are used to specify the data needed in a stock-turnover calculation.  Using this approach, energy consumption is calculated by analyzing the current and projected future stocks of energy-using devices and the annual energy intensity of each device (defined as energy per device).

Transport Analysis branches are used to specify the data needed in a transport stock turnover calculation.  In this approach energy consumption is calculated as the product of the number of vehicles, the annual average mileage (i.e. distance traveled per vehicle) and the fuel economy of the vehicles (e.g. liters per km or 1/MPG).

Note: in general you cannot mix branch types in immediately neighboring branches, so, for example, category and technology branches cannot be placed together within the same tree folder. Because of this restriction you sometimes may not be able to change the type of an existing branch if it already has neighboring branches.  The exception to this rule is that green and yellow category branches can be placed next to each other.

Tips for Specifying Branch Names

When specifying the name of a branch in most cases you simply need to type a name in the Name box.  In order to avoid conflicts with LEAP's built-in mathematical functions, some names are not allowed.  LEAP will automatically check the name you enter and alert you to any conflicts.  Note that the OK button will be disabled until you have entered a valid name.

When creating a technology branch you will often simply want to name the branch the same as its associated fuel.  To avoid extra typing, you can first choose the fuel from its selection box and LEAP will then use that as the branch name.  To quickly select a fuel type the first few letter of its name.  For example, type "el" to quickly select electricity.  After selecting a fuel you can always edit or override the branch name by editing the text in the name box.

Special Properties When Energy Demand Data is Time Sliced

In normal circumstances, energy demand data are specified annually.  The seasonal and time-of-day variations in energy demands are specified later on by specifying the load shape for the entire electric system in each Transformation module.  However, on the General: Settings: Loads screen you can instead choose to specify the load shapes of each individual demand device.  If you have chosen this approach then the Demand Branch Properties screen will show additional options that let you specify how energy consumption in these devices varies by time slice.

The three options are: